Litter robot flashing lights
Litter-Robot 4 is the latest evolution of the highest-rated WiFi-enabled, automatic, self-cleaning litter box for cats. With over 20 years of customer feedback driving product innovation, Litter-Robot 4 features new sensor and litter-sifting technology for enhanced odor control, cat safety, and real-time tracking of waste and litter levels through the Whisker app.BLUE FLASHING (A) Drawer full: Drawer / waste bin is full; DFI sensor lens needs cleaning; Empty drawer ; Install new liner; Press reset; Article; BLUE FLASHING (B) DFI sensor issue. DFI sensor needs replacing; Replacement Guide (H) YELLOW SOLID: Cycling (In use) Working normally; Without rotation DFI sensor or Motor defective; Normal use ...The Litter-Robot utilizes position sensors to determine the position of the globe during rotation. Additionally, the speed of the globe is calculated to ens...
Did you know?
The blue light may flash if the sensors are not clean. Litter Clumps Stuck in Gears: Sometimes, clumps of litter can get stuck in the gears of the Litter Robot, causing it to malfunction and display a blue light. Power Supply Issues: A fluctuating power supply or inadequate power can also lead to the blue light flashing.If your litter robot 3 is not able to complete a cycle and is flashing yellow randomly, then watch this video for the fix!Our litter robot was giving us nigh...Jan 23, 2024 · The Litter-Robot is equipped with an Anti-Pinch Safety Feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch conditi... Resolve issues with your Litter-Robot 4 showing a blue light bar with partial yellow flashing. Learn how to troubleshoot excess weight detection, ensure accurate SmartScale™ readings, and update firmware for optimal performance. ... Unsuccessful: If you are still seeing a blue light bar with partial yellow flashing after resetting at the Home ...I recently purchased a litter robot 3 connected and the litter robot has been working perfectly up to this point, however, since I did my first litter empty the unit will not reset properly. I have the flashing blue light constantly. I press the reset button and I can get the blue light to remain steady but after one cycle it is back to flashing and …Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. ... blue light flashing - waste drawer empty . Litter-Robot 3 hello! my robot has had a flashing blue light for the past few days even though the waste drawer is empty. it will cycle every now and then but not as often as it should. any ideas? Share Add a ...The litter is above the fill line or in excess of 10lbs. The unit is sitting on an uneven surface ‐ grout lines on a tile floor or in a bathtub. The red blinking light indicates CATS (the cat sensor) is detecting excess weight for more than 2 minutes. To test your changes, power the unit off and then on.Step 1: Check the Power. The first thing to do when it comes to troubleshooting a Litter Robot that is stuck mid-cycle is to check the power. Make sure the unit is plugged in and the power cord is securely connected to the unit and the outlet. If the power cord is loose, securely reconnect it. If the outlet is not functioning, try plugging the ...I receive really interesting update from Litter-Robot. To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. Preparation. Litter-Robot 4 continuously monitors the motor current to ensure the globe is rotating smoothly and is not obstructed. If your unit has a red light bar with partial yellow flashing, this indicates that the globe is most likely jammed or overloaded. The unit will retract and try to continue cycling. I got an email back yesterday about this light sequence (that I sent in December) Hello Problematikuav, Thank you for trying the troubleshooting. I am sorry to hear your Litter-Robot is giving you this trouble. I looked into your serial number on the backend, and your unit is on outdated software!Hi everyone. My litter robot connect has issues. Yellow light is flashing rapidly. Have replaced pinch detectors and they are touching. Have checked also night light connection and all 3 lights inside bot is working. Still have issue. Would anyone have any idea what's wrong with it. Any advice will be much appreciated.Make certain you have the DFI shields clean of any debris or smudging of debris. This will cause the slow flashing blue light. Next check your weight sensor connection, its located behind the waste drawer in the center back of the base unit, this being disconnected will cause the slow flashing red light on power up.Unfortunately these litter robots do not replace scooping, and we have to keep a regular litter box as backup for when these units fail. Reply reply More replies ... If you are experiencing a yellow flashing light and/or the cycle has been interrupted and the globe is stuck, it could be due to excess weight, the bonnet, or the anti-pinch safety ...Every Litter-Robot 4 includes the WhiskerCare™ 1-Year Warranty with option to extend to 3 years. Free shipping. Your order ships free when you spend $49+ on any of our products (excl. AK, HI, PR). You and your cat deserve a better litter box. Shop LItter-Robot 4. Facebook; Twitter; Instagram; YouTube; Pinterest;Successful: If your Litter-Robot displays a blue lightIf your Litter-Robot 3 is displaying a yellow light flashing slow Status Indicator Lights. Solid Blue: Feeder is in Automatic Feeding Mode. Solid Yellow: Hopper is low indicating less than 20% food remaining. Solid Red: Hopper is critically low indicating less than 5% food remaining. Flashing Red: Dispenser is jammed. Solid Purple: Food Bowl and Food Chute are full for 12+ hours (food has not been consumed)Came home to my Litter-Robot in the upside down position and the yellow flashing (2 flashes per second) and I cannot get the globe to turn at all to try to reset itself. There is power to the unit because the yellow light is flashing but regardless of which buttons I press or turn power on/off no movement of the unit can be made. Toll Free: 877-250-7729 www.Litter-Robot.com Remove your backup battery from the LR 4. Then plug this in to the wall, and then the LR4 into it, and get the app. When you get the 3 Blue 2 Yellow warning, and it refuses to cycle, use the SmartPlug app to kill power to the SmartPlug, then turn it on again. The LR 4 will reset itself and cycle again. This is a dumb workaround, but it works in ... Litter Robot 4 won't flash yellow wifi light to connect to
The following are the typical causes of why your Litter-Robot is having torque issues: 1. Motor Obstruction. The globe of the Litter-Robot can get jammed at one point while using the litter box. This causes the motor to stop and will display yellow and red lights blinking in sequence. Recommended: How to fix yellow light flashing in Litter ...The Litter-Robot will now perform an initial clean cycle. Need help? Visit whiskersupport.com Use clumping litter or litter beads and crystals that are small enough to pass through the screen. Add litter until it meets the raised MAX fill line when spread flat (8-10 lbs or 3.6-4.5 kg). Be careful not to overfill. Download the Whisker app and ...If your Litter-Robot 3 troubleshooting is more complex than the scenarios described above, you’ll likely get lights flashing sequentially: Flashing yellow to red means the motor has detected an obstruction or jam. Turn that unit off and remove that bonnet and globe. Check to gear or motor obstruction.All with the red and yellow flashing lights. It would just start to cycle-stop than, flashing lights. Get 1/4 of the way into a cycle, flashing lights. Make it all the way to dump and start to head back to the ready position, flashing lights. Complete an entire cycle, instead of the blue ready light, flashing lights.
The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...Litter-Robot 4 features a Bonnet that covers the Globe and functions as a guard for the Waste Port as the Globe rotates.Sensors on the unit detect if the Bon...The first magnet needs to go into the closed-in area next to the waste opening on the globe. Take a small piece of tape and tape this magnet into position.3. The two closed areas that are right next to each other aren't used for the magnets, so please ignore those. The second magnet goes in that last closed area.…
Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. This may take up to 30 minutes to complete. You will see a single w. Possible cause: Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks.
Disconnect the bonnet. Gently flex the two front bonnet tabs outward and hold for about 20-30 seconds. Reattach the bonnet. There are four tabs total: two in the back, two on the sides. You should feel a secure snap and hear a "click" when placed back into the slot, and the bonnet should sit closer to the base.litter-robot-3-connect, litter-robot-3. Bebexpxo89 August 3, 2020, 12:25am 1. My unit is BRAND NEW. Email customer service they sent me the email they sent to everyone. …This video shows you how to get the 3 lights on the Litter-Robot 3 to stop blinking. Litter-Robot 3 Buying Options: 💵 Worried about your cats using it? Wan...
Reboot your router. Completely close the Litter-Robot app. While the unit is at the Home position with the solid blue light, unplug your unit from the BASE, not the wall. Wait 15 seconds, plug it back in, and allow it to cycle until the solid blue light comes on (“Ready” status). Open the app and follow the steps.1. When your cat exits the Litter-Robot, a timer counts down, allowing the litter to clump before the clean cycle begins. 2. During the clean cycle, the globe slowly rotates. The patented sifting process separates the clumps from the clean litter. 3. The clumps are deposited into a fully enclosed waste drawer located below the globe with a ... The shield is a possible cause for the three lights flashing fault. We strongly recommend removing the internal shield. If your Litter-Robot was built before February of 2018, you may have an internal shield. The internal shield is not necessary for the unit to function and was removed from the design in March 2018.
Unplug it let it sit for a couple of minutes plug it back So woke up this morning with litter robot 4 offline. The big light is solid blue with the little light flashing blue. How do I reconnect it? I pressed the wifi button once, goes to solid light yellow, pressed it again and goes back to blinking blue. If I press the wifi for 3 seconds, goes to flashing yellow, but nothing happens on the app. Preparation. Litter-Robot will detect if the wrong power supply is beRemove the 10 screws around the y-axis of the globe. Set the The unit should resume its previous function five seconds after the bonnet is replaced and return to Home position displaying a blue light bar. Successful: If your unit returned home and displays a blue light bar, you've been successful. Unsuccessful: If you are still seeing a yellow light bar flashing, there's likely an issue with your Litter ... The tray's empty and the light still blinks with or without a bag. No MOD. Can't get flashing blue "drawer full" light to clear. So I've got a recurrent problem with the flashing blue light, which the instructions and research tells me means the waste bin/drawer is full. But I've completely emptied it several times, and still the flashing blue light persists. If I press the "reset" button it will turn to solid ...Litter-Robot utilizes position sensors to determine the position of the globe during rotation. Additionally, the speed of the globe is calculated to ensure continued operation as a backup to the position sensors. If your unit displays a red light bar with partial white flashing, this indicates that the unit did not detect the globe position ... How to change the Wait Time setting on Litter-REighty lumens is sufficient to cause tempoPreparation. Litter-Robot 4 continuously moni Learn how to troubleshoot indicator lights for the LitterMaid Automatic Litter Box. The Litter-Robot is equipped with an Anti-Pinch safety feature t AudioVOX May 26, 2015, 3:51pm 1. Considering we’ve received a huge response on our Litter-Robot II Basic Troubleshooting Guide, we’ve decided to help our customers further by creating this advanced troubleshooting guide. This guide will help you with opening up the Litter-Robot II to verifying connections of the motor and circuit board. The Litter Robot starts a cycle AS SOON AS YOU POWER IT ON.Posting to hopefully help someone else that was being drove nuts The red blinking light indicates CATS (the cat sensor) is detecting excess weight for more than 2 minutes. In this comprehensive tutorial video guide, Aiman...The Litter-Robot will now perform an initial clean cycle. Need help? Visit whiskersupport.com Use clumping litter or litter beads and crystals that are small enough to pass through the screen. Add litter until it meets the raised MAX fill line when spread flat (8-10 lbs or 3.6-4.5 kg). Be careful not to overfill. Download the Whisker app and ...